Skip to main content

Posts

High Current Power Supply Circuit with 2N3055

This is a unregulated dc power supply circuit which have ability to handle high current load. Component parts: R1_________ 680 Ohm 1/4 Watt Resistor C1_________ 20,000 - 50,000uF 20-40 Volt Capacitor C2, C3_____ 100uF/50 Volt Capacitor C4_________ 0.1uF 50 Volt Capacitor C5_________ 0.01uF 50 Volt Capacitor D1_________ Zener Diode Q1_________ 2N3055 Or Other T1_________ Transformer BR1________ Bridge Rectifier S1_________ SPST 250 VAC 10 A Switch MISC_______ Case, Line Cord, Heatsink For Q1, Binding Posts For Output NOTES: D1 should be rated at about one volt higher than then desired output of the supply. A half watt diode will do. Q1 can be a transistor similar to the 2N3055. T1 should be about 5 volts higher than the desired output of the supply, and rated for about one amp more of current. The voltage overhead is required by the regulator section. The extra current is to keep the transformer from over heating. The choice of BR1 will depend on the voltage and current of your transf...

Uninterruptible Power Supply circuit

Here the Uninterruptible Power Supply (UPS) circuit with PIC17C43 microcontroller. Your UPS will be automatically controlled by the microcontroller. UPS systems are traditionally designed using analog components . Today these systems can integrate a microcontroller with AC sine wave generation, offering the many benefits. The PIC17C43 microcontroller handles all the control of the UPS system. The PIC17C43 is unique because it provides a high performance and low cost solution not found in other microcontrollers. Download the document of Uninterrupted Power Supply

5-18V Stabilized Power Supply

This power supply will give you fixed regulated output at 5V, 6V, 9V and 12V, while the 18V output is unregulated. You could add some regulated IC like LM7815 or 7818 if you need higher output voltage. This circuit provide an audio indicator that will act like an alarm if any circuit short contact.

General DC Power Supply with uA723

This is the power supply circuit for general purpose usage. The supply can be used for supply output voltages from 1 to 35V. The line transformer should be selected to give about 1.4 times the desired output voltage from the positif side of filted capacitor C1 to ground. Potensiometer R2 sets the output voltage to the desired value by adjusting the reference input. Rsc is the current limit set resistor. For example, if the maximum current output is to be 1A, Rsc=0.65/1.0 = 0.65 Ohm. The 1KOhm resistor,R5, is a light-loaded resistor designed to improve the no-load stability of the supply.

Universal Battery Charger

Battery charger for general purpose usage. The charger's output voltage is adjustable and regulated, and has an adjustable constant-current charging circuit that makes it easy to use with most NiCad batteries. The charger can charge a single cell or a number of series-connected cells up to a maximum of 18V. Power transistors Q1 and Q2 are connected as series regulators to control the battery charger 's output voltage and charge-current rate. An LM-317 adjustable voltage regulator supplies the drive signal to the bases of power transistor Q1 and Q2. Potensiometer R9 sets the output-voltage level. A current sampling resistor, R8 (a 0.1 ohm/5W unit), is connected between the negative output lead and circuit ground. For each amp of charging current that flows through R8, a 100mV output is developed across it. The voltage developed across R8 is fed to one input of comparator U3. The other input of the comparator is connected to variable resistor R10. As the charging voltage across...

Adjustable Power Supply 3-30V/2.5A

This is an adjustable power supply circuit , also known as variable power supply. . You may use this circuit for general purpose usage. Here the schematic diagram : Component list: R1 = 560R 1/4W C1 = 100nF R2 = 1,2 K 1/4W C2 = 2200uF 35-40V R3 = 3,9 K 1/4W C3 = 100 pF R4 = 15K 1/4W C4 = 100uF/ 35V R5 = 0,15R 5W D = B40 C3300/2200, 3A rectifier bridge P1 = 10K potesiometer TR1 = BD 135 ...

Variable DC Power Supply with 2N3055

This is variable power supply for multi purpose usage and very useful to supply your electronic tools or your projects. Voltage range will be 0.7 - 24V and the urrent limiting range is 50mA - 2A. Components: P1____________500R Linear Potentiometer P2_____________10K Log. Potentiometer R1,R2__________2K2 1/2W Resistors R3____________330R 1/4W Resistor R4____________150R 1/4W Resistor R5______________1R 5W Resistor C1__________3300µF 35V Electrolytic Capacitor (see Notes) C2_____________1µF 63V Polyester Capacitor D1,D2_______1N5402 200V 3A Diodes D3____________5mm. Red LED Q1___________BC182 50V 100mA NPN Transistor Q2___________BD139 80V 1.5A NPN Transistor Q3___________BC212 50V 100mA PNP Transistor Q4 _________2N3055 60V 15A NPN Transistor T1____________220V Primary, 36V Center-tapped Secondary 50VA Mains transformer (see Notes) PL1___________Male Mains plug SW1___________SPST Mains switch Notes: P1 sets the maximum output current you want t...